Silverline 1200W Sander Polisher Manuel d'utilisateur télécharger pdf (Page 5)

Carefully read and understand this manual and any label attached to the tool

before use. Keep these instructions with the product for future reference. Ensure

all persons who use this product are fully acquainted with this manual.

Even when used as prescribed it is not possible to eliminate all residual risk

factors. Use with caution. If you are at all unsure of the correct and safe manner in

which to use this tool, do not attempt to use it.

General Power Tool Safety

Warnings

WARNING Read all safety warnings and all instructions. Failure to follow the

warnings and instructions may result in electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded)

power tool or battery-operated (cordless) power tool.

Work Area Safety

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents

b) Do not operate power tools in explosive atmospheres, such as in the

presence of ﬂammable liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes

c) Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control

Electrical Safety

a) Power tool plugs must match the outlet. Never modify the plug in any

way. Do not use any adapter plugs with earthed (grounded) power

tools. Unmodiﬁed plugs and matching outlets will reduce risk of electric

shock

b) Avoid body contact with earthed or grounded surfaces, such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded

c) Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock

d) Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords increase the risk of electric

shock

e) When operating a power tool outdoors, use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use reduces the risk of

electric shock

f) If operating a power tool in a damp location is unavoidable, use a

residual current device (RCD) protected supply. Use of an RCD reduces

the risk of electric shock

NOTE: The term “residual current device (RCD)” may be replaced by the

term “ground fault circuit interrupter (GFCI)” or “earth leakage circuit breaker

(ELCB)”.

Personal Safety

a) Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired

or under the inﬂuence of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in serious personal injury

b) Use personal protective equipment. Always wear eye protection.

Protective equipment such as dust mask, non-skid safety shoes, hard hat,

or hearing protection used for appropriate conditions will reduce personal

injuries

c) Prevent unintentional starting. Ensure the switch is in the off-position

before connecting to power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your ﬁnger on the switch or

energising power tools that have the switch on invites accidents

d) Remove any adjusting key or wrench before turning the power tool on.

A wrench or a key left attached to a rotating part of the power tool may result

in personal injury

e) Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts

g) If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly used. Use

of dust collection can reduce dust-related hazards

Power Tool Use & Care

a) Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the

rate for which it was designed

Description of Symbols

The rating plate on your tool may show symbols. These represent important

information about the product or instructions on its use.

Wear hearing protection

Wear eye protection

Wear breathing protection

Wear head protection

Wear hand protection

Read instruction manual

Double insulated for additional protection

Conforms to relevant legislation and safety standards

Environmental Protection

Waste electrical products should not be disposed of with

household waste. Please recycle where facilities exist. Check

with your local authority or retailer for recycling advice

Speciﬁcation

Voltage ............................................................. 230V~/50Hz

Power ..............................................................1200W

No load speed .................................................. 600 – 3000min

-1

Spindle thread ..................................................M14, male

Backing Pad diameter ......................................180mm

Weighted vibration ...........................................6.51m/s

Uncertainty.......................................................1.5m/s

Sound pressure ................................................84.1dB(A)

Sound power ...................................................95.1dB(A)

Uncertainty................................................. ..... 3dB

Weight .............................................................3.54kg

Protection Class: ..............................................

As part of our ongoing product development, speciﬁcations of

Silverline products may alter without notice.

The sound intensity level for the operator may exceed 85dB(A) and

sound protection measures are necessary.

Sound and vibration levels in the speciﬁcation are determined according to

EN 60745. The ﬁgures given can be used to compare similar tools tested to

this standard. These ﬁgures may be used to assess exposure to noise and

vibration levels.

The ﬁgures represent normal use for the tool in normal working condition.

A poorly maintained, incorrectly assembled or mis-used tool may produce

increased levels of noise and vibration. The total working period that

you can operate this tool must factor in periods where the tool is idle or

switched off. Allow frequent rest breaks when operating this tool.

It is in the interest of users to maximise their safety using the correct safety

equipment like ear defenders that protect against loud or repetitive noise

and anti-vibration gloves that minimise vibration. Do not operate the tool

with your hands below a normal comfortable temperature as vibration will

have a greater effect.

www.osha.europa.eu provides information on sound and vibration levels in

the workplace that may be useful to domestic users who use tools for long

periods of time

264569_Z1MANPRO1.indd 4 04/03/2013 12:19

1 2 3 4 5 6 7 8 9 10 ... 27 28

Commentaires sur ces manuels

Pas de commentaire

Silverline 1200W Sander Polisher Manuel d'utilisateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Silverline 1200W Sander Polisher